ejecting

英 [iˈdʒektɪŋ]

美 [iˈdʒektɪŋ]

v.  驱逐; 逐出; 赶出; 喷出; 喷射; 排出; (飞行员在飞机坠毁前从弹射座椅)弹出
eject的现在分词

柯林斯词典

• VERB 驱逐;把…逐出
  If youejectsomeonefroma place, you force them to leave.
  1. Officials used guard dogs to eject the protesters...
     官员们用警犬驱散抗议人群。
  2. He was ejected from a restaurant.
     他被逐出餐厅。
• VERB 弹出;喷出;射出
  Toejectsomething means to remove it or push it out forcefully.
  1. He aimed his rifle, fired a single shot, then ejected the spent cartridge.
     他用步枪瞄准，射出一枚子弹，然后退出空弹壳。
• VERB （通常指飞行员从即将坠毁的飞机中）弹射出来
  When a pilotejects froman aircraft, he or she leaves the aircraft quickly using an ejector seat, usually because the plane is about to crash.
  1. The pilot ejected from the plane and escaped injury.
     飞行员从飞机中弹出，安然无恙。

双语例句

• The influence of the working fluid pressure and the structure of ejecting nozzle on the outlet temperature, ejecting coefficient and heating efficiency of the ejecting-mixing heater were analyzed.
  对多喷嘴引射混合式加热器的加热性能进行了试验研究，分析了工作流体压力和引射孔结构对引射混合式加热器的出口温度、引射系数以及加热效率的影响。
• Based on a double foundation characteristic, two schemes of high pressure ejecting grout plank wall and ballast for preventing piping and soil flow were investigated.
  根据双层地基的特点，分别对复合土工膜堆石堤堤基采用高压喷射灌浆板墙方案和压重防止管涌流土方案的防渗效果及经济性进行了计算比较。
• The Study and Calculation of Gas Filling and Ejecting Characteristics of Gas-propelled APDS
  气推式脱壳弹充排气规律研究与计算
• Ejecting coefficient decreases while the distance between water nozzle and mixed spout increases.
  在入口水压一定的条件下，喉嘴距较大时引射系数较小；
• Finally, the location and size of the ejector pins that correspond to the discrete ejecting forces are obtained.
  最后，这个位置和大小的异形销，迎合了离散排出力量。
• Excitation radiation may do this by penetrating to the cathode and ejecting a photoelectron. Some of the excited atoms undergo radiative deexcitation.
  激发辐射可能射到阴极，逐出一个光电子，从而引起这个。某些受激的原子会发生辐射性退激。
• Instead, after 38 years his Quantum fund is ejecting investors to run only the family inheritance.
  在成立38年之后，他的量子基金开始将投资者拒之门外，从今以后将只管理家族财产。
• The design of side core-pulling framework and ejecting framework is difficult in designing injection mould.
  侧面抽芯机构和顶件机构的设计是注射模具设计的难点。
• Design injection mould with quadratic ejecting mechanism of slider and wedge dual push plate
  推床的导板（或推板）滑块斜楔双推板式二次推出机构注塑模的设计
• Ejecting and heating performance of the heater at low steam pressure was studied through the experimental method.
  用试验方法研究了该加热器在低进汽压力下的引射性能和加热性能。